Previously reported, Apple released the iOS 5.11 and shortly after, a jailbreak is available for A4 chip devices such the iPhone 3GS, iPhone that was accidentally update to the iOS 5.1.1 firmware version. Unfortunately, the jailbreak still tethered.
The iPhone Dev Team has once again within a few hours updating the redsn0w jailbreak tool equipped with a small improvement. released only a few hours after the iPhone Dev-Team has 0.9.10b8 redsn0w, which is the protection of the activation of tickets IMSI Unlock , there is already a new version of the jailbreak tools available for download.
Redsn0w 0.9.10b8b brings little new with it, no iOS 5.1 jailbreak for the iPhone 4S or iPad 2. However, a small optimization for the aforementioned new backup feature that allows backups of folders from the file system.
Not compatible with his instructions to jailbreak pod2gs to be with older devices that are compatible with iOS 5.1.1: Apple TV 3, iPod Touch 3G and iPhone 3G. These are devices that have been published before the A4 processor. The reason given is that the kernel vulnerability is not there.So it’s not iOS 5.1.1, but the hardware. Will continue but under iPhone 3G and iPod Touch 3G jailbreak redsn0w tethered the 0.9.10b6 be possible.
The tethered jailbreak can currently be installed on IOS devices:
- iPhone 4
- iPhone 3GS
- iPod touch 3G
- iPod touch 4G
- iPad first Generation
Are not supported:
- iPhone 4S
- iPad 2
- iPad 3
The new devices Untethered Jailbreak is already in development and the jailbreak community is working very hard on an appropriate solution.The hacker Pod2G already has some successes, but the release of IOS 5.1.1 is likely to cost him additional time.
Important:
Before you follow the instructions, you should make it a backup of your device.If you connect your device with iTunes, automatically backed up.Otherwise, even on the icloud (Settings -> icloud -> Storage & Backup -> Create backup now), a backup can be initiated.
Tethered Jailbreak Guide for iOS 5.1.1 with redsn0w 0.9.10b8b:
Tethered Jailbreak 5.1.1 with redsn0w iOS 0.9.10b8b
Step 1:
First you need the IOS version 5.1 for your device and the respective version of redsn0w 0.9.10b8b download.
Download links for IOS 5.1:
Here are the download links for redsn0w 0.9.10b8b:
Step 2:
Start the program redsn0w and selected under Tools -> Select IPSW -> the downloaded iOS 5.1 Firmware for your device.After redsn0w has identified the firmware successfully, return it to the home screen of redsn0w.
Step 3:
Click on “Jailbreak”.
Step 4:
Next, you’ll have to connect your device on and off with your computer.Then follow the instructions and click Next.
Step 5:
You must bring your device now in DFU mode.For this press the “Power” button on your device for 3 seconds.Then you have to be the “Home” and “Power” button press for 10 seconds.Then she lets the “Power” button and go wait until the installation begins in RedSn0w.
Step 6:
Once you have successfully brought your device in DFU mode, initial preparations are done for the jailbreak, it will automatically detect your device and load the appropriate files.
Step 7:
After the window shown below appears and you must check “Install Cydia” put everything off others.Continue by clicking Next.
Step 8:
The installation will be carried out and after that your IOS device automatically restarts.It shows that the tethered jailbreak and Cydia is ready installed on your machine.
Instructions for the tethered boat:
This makes it this is a tethered jailbreak, your unit comes with every reboot or power loss in a boot loop.You can use your device as long as not, to her a tethered boat you have done.Unfortunately, you have to perform this operation on every reboot!
Step 1:
You must first connect your device to your computer and launch RedSn0w.Then click on “Tools”.
Step 2:
Next, you must “boot Just” click on it to start the tethered boot process.
Step 3:
You must now turn off your device and click “Next”.
Step 4:
You must bring your device now in DFU mode.For this press the “Power” button on your device for 3 seconds.Then you have to be the “Home” and “Power” button press for 10 seconds.Then she lets the “Power” button and go wait until the installation begins in RedSn0w.
Step 5:
Now it takes about a minute until the process is carried out.Then you will see a pineapple on your screen.After a short wait, your unit is restarted and you can use it.
Instructions for installing SemiTether:
Step 1:
Open Cydia, click Manage, and select sources
Step 2:
Click on Edit, Select Add and add the following source:
http://thebigboss.org/semitether
Step 3:
After looking into Cydia and install after SemiTether.The unit is then restarted and needs to be booted using redsn0w again (Tools -> Tethered boot)
Step 4:
Finally, open the app and SemiTether enable the Safari patch.After that, the device boot up even after a reboot without redsn0w and Safari are working normally.
